Home Specials Contact Us

Beissbarth

Challenger E10
Challenger E10

Specifications
Lifting Capacity * 10,000 lb. (4536kg)
Rise Height ¹ 75¾" (1924mm)
Column Height 11' 11⅞" (3655mm)
Overall Width 10' 11¾" (3347mm)
Drive-thru Clearance 98⅜" (2499mm)
Floor to Overhead Switch 11' 5" (3482mm)
Front Arm Reach 21¾"- 39½" (553-998mm)
Rear Arm Reach 38¼"-55⅜" (971-1407mm)
Screw Pad Height ² Adj. 4˝" - 7½" (103mm - 194mm)
Inside of Columns 110¼" (2800mm)
Ceiling Height Required ³ 12' (3658mm)
Motor 2HP, Single Phase, 60Hz
Voltage 208 - 230v
Speed of Rise 50 seconds
Max. Load Per Arm 2,500 lb. (1134kg)
* Lift capacity ratings are based on loads equally distributed on all four arms.
1 Rise height measured with telescoping screw pad in highest position
2 Specifications are listed without rubber pad, for measurements with rubber pad add 1/4˝(6mm).
3 Ceiling height requirement may exceed 12' if column shimming is necessary.

Stenhøj MAJOR 4030 W - Electro-Hydraulic 4-wheel Alignment Lifts
Stenhøj MAJOR 4030 W

Specifications
  • Major 4030 W has 1020 mm recesses with 3 fillers.
  • The recess is equipped with an adjustable plate for turntables with heights from 22 to 50 mm.
  • Both models are equipped with fineadjustable 1990 mm slip plates with a height of 19 mm.
  • A min. height of 160 mm incl. slip plate gives easy access via only 760 mm ramps.
  • The ramps are delivered prepared for fitting of 395 mm extensions (option).
Lifting capacity 4000 kg
Lifting time 22 sec.
Lifting height 1820 mm
Min. height 160 mm
Motor 3 kW
Min./max. pressure 5/10 bar
Standard colours Red RAL 3013 / white RAL 9002
Special colour combinations available on request.

Stenhøj MARSHAL 30-04 - Electro-Hydraulic Scissor Lifts
Stenhøj MARSHAL 30-04

Specifications
  • Elegant control box with dead-man controls and separate main switch.
  • Automatic air-operated parking system.
  • A parking system; which also by means of the ratchet rail system prevents unintentional lowering.
  • Starting system which ensures steady starting procedure at full capacity (3 t).
  • Ramps function as extensions.
Lifting capacity 3000 kg
Lifting time 39 sec.
Motor 3 kW
Min./max. pressure 6/10 bar
Standard colours Red RAL 3013 / white RAL 9002
Special colour combinations available on request.

Stenhøj MIRO 2.30 F - Electro-Hydraulic Scissor Lifts
Stenhøj MIRO 2.30 F

Specifications
  • Cold-rolled, centred spindle with quadrupled life.
  • Nut breakage system
  • Arms can be parallel-parked.
  • Synchronization via non-contact tracking that realigns at disalignment of more than 15 mm.
  • Door stops of rubber effectively protect vehicle door when being opened.
  • Extremely low minimum height – only 85 mm.
  • A large program of flex pads in different heights.
Lifting capacity 3000 kg
Lifting time 54 sec.
Motor 2 x 2.8 kW
Lifting Height 2015 mm
Standard colours Red RAL 3013 / white RAL 9002
Special colour combinations available on request.